How to Replace the Headband On Beats Studio 2 Headphones

The Beats Studio 2 wired and wireless headphones have a plastic arch that connects the two metal hinges that say "Studio" or "Wireless". This arch will frequently snap just above the metal hinges if put under too much strain. This article shows you how to replace that plastic arch. 

 

If you would prefer to read a written repair guide, check that out below. Or if the tool cost seems prohibitive for a one time repair and you would prefer that we complete this repair for you, check out our Repair Catalog to see if we offer repair services for this device. 

Are you a business? We offer wholesale discounts on our repair services if you are sending numerous units in for repair or want to send us continuing batches of devices for repair on a regular basis. Contact our support team for more info Info@JoesGE.com (This email is only for wholesale inquiries, please contact Support@JoesGE.com for other inquiries).

_____________________________________________

 

Repair Difficulty: Easy

Time to complete: 15 Minutes

The tools and parts that you will need for this repair:

    1. New Headband 
    2. T5 Screwdriver (To remove four screws)
    3. Pry Tool  (Thin plastic screwdriver, a guitar pick, or the dull side of a butter knife can all work if you are careful).

_____________________________________________

 

1. Unscrew the screws from both sides of the hinges

There are four screws holding the headband into place. There are two on the bottom of each hinge. Fold the hinge inward to gain access to them. 

Unscrewing the hinge screws

 

2. Remove the broken headband

Once you have removed all four screws, your headband should slide out from the hinges. If part of the headband has broken off inside of the hinges, you should just be able to shake the hinge and have it fall out. Remember the orientation of the Beats logo on the top of the headband for when you install your new headband so that it is not backward.

***If you previously tried gluing the headphones back together, you might need to get some tweezers or pliers to remove any plastic bits that are stuck in the hinges. If you are unable to remove them due to glue, you might need to use something like Acetone to remove the glue which will also remove the paint on the hinge and can damage the wiring if you let it get on the headphones. If you would prefer, we can usually remove the plastic, or if it comes down to it, we can replace the hinge on your headphones if you send them in by following the steps Here. 

 

3. Remove the headband cushion

Using your Pry Tool, start at one end of the rubber headband cushion and pry it away from the plastic headband. There is a plastic frame inside of the rubber cushion that uses snap connects to stay attached to the headband. Once you have one entire side removed from the headband, you should be able to easily remove the whole cushion from the headband. 

Removing the headband cushion 

4. Insert the new headband into the hinges

Just make sure that the Beats logo is facing forward. You should be able to read it regularly if you are looking at the front of the headphones. 

 Aligning the headband

5. Clip the headband cushion onto the headband

You will need to make sure that the large main wire is centered properly in the plastic headband before attaching the headband cushion. This can take some time so put on your favorite tunes and get it just right :)

Once it is centered, just apply pressure to the front and back of the cushion to snap it onto your headband. When done, it should look like this:

Removing the headband cushion

Those two rubber ends that are stick out all funny need to be put around the main wire, and tucked into the metal hinge. Fold one side of the headphones inward like so:

Fold one side of the headphones

Then remove the other hinge from the headband and run the wire through the inside of the two rubber flaps on the end of the headband cushion, like so:

The rubber flaps

Once you have the wire tucked into the rubber, slide the hinge back onto the headband and headband cushion and insert both screws into that sides hinge.

Repeat this process for the other side of the headphones. 

 

6. Now get back to jamming out 🎶

If you have any questions in regards to this repair feel free to shoot us an email or text and we will do our best to reply to you as quickly as possible. Please inquire using our Repair Catalog if you are wondering how much a certain repair will cost. If you do not see your item in our repair catalog, it means that we do not offer repair services for it. 

📧 Support@JoesGE.com

💬  360.362.1722

Previous article How to Replace the Headband On Beats Studio 3 Wireless Headphones
Next article Solo 3's Won't Turn on or One Side Isn't Working? Beats By Dre Solo 3: 5-core Wire Replacement